Just How to Remove and Change a Tub
Just How to Remove and Change a Tub
Blog Article
This post down below on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is particularly insightful. You should investigate for yourself.
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a new one is also a reasonably hard job. If the old bathtub is conveniently available, the task can move quickly; if you have to open up a wall to remove the old bathtub as well as position the new bath tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub as well as set in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. Rather than working with a professional to take over a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your shower room if you have already bought a brand-new tub and also don't require to change the plan of your previous water supply pipes.
Your devices as well as product checklist need to make up the following:
Planning for the Installment
First of all, the supporting frame provided with the bath needs to be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its final setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using both wood boards under its feet, place the bath tub in the needed setting. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by checking the level as well as readjusting the feet on the tub until the level reads degree.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, take care of the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the bathtub must wait until the tub has actually been utilized at the very least once as this will settle it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the maker supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former kind needs to be connected to the tap ends initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, triggering the water to permeate the wall between the bath and also the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can fracture fairly very early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that article about How to Install a Bathtub Yourself through a good friend on our other web page. Liked our entry? Please share it. Let other people locate it. Thanks for going through it.
Booking
Report this page